Trim enabler old mobo pro#

Therefore, I opened it up again and switched everything around. It was only after putting everything back together that I realised the interface for the DVD drive caddy (PATA) may be slower than the actual SATA interface that the main drive runs off. In the following photos, I havenвЂ™t done this. This isnвЂ™t strictly neccessary though вЂ“ your SSD will function in the new caddy, but may not be the best performance possible. IвЂ™d also suggest removing the existing hard drive at this point, so we can fit the SSD to the main drive location and the existing drive to the extra caddy we are fitting now. There are 4 screws holding the DVD in place вЂ“ a T6 by the top left (next to the cable), 2 tiny Phillips screws at the front, and a further one at the back. When you can, carefully pull off the ribbon cable from the motherboard using a plastic spatula. The front section may be difficult to remove вЂ“ вЂњwigglingвЂќ may be neccessary. DonвЂ™t lift so much that it pulls off, or youвЂ™ll end up with a doorstop. Be very careful of the ribbon cable connected to the motherboard underneath though. Lifting from the back, you should now be able to remove the entire keyboard section. Turn the machine around and carefully lift open the screen. Next remove the screws on the edge of the case there are 4 on the left and right sides, as well as two on the back hinge. Use a piece of paper to actually draw the outline of your Macbook and distinguishing features if it helps. Hint: I place all the screws removed on a kind of mini diagram as to where they should go back вЂ“ there are varying lengths and threads, so itвЂ™s important you donвЂ™t mix them up. There are 4 Phillips screws along the back, 2 Torx next to the memory, and 2 Phillips on the inside wall of the battery compartment. You can remove the memory too, but itвЂ™s not necessary. Then remove the 3 screws holding the memory plate in place, and slide it out the plate. If youвЂ™re using a different model, check out the hard disk and DVD removal guides at .Д«egin by removing the battery pack via the two clips. However, this can also be done on other Macbook models.

Trim enabler old mobo pro#

IвЂ™m working with a late 2006 Macbook Pro today вЂ“ itвЂ™s a non unibody, aluminium design. Newer Macbook models have a SATA connection to both, so check your exact model first.

When buying a DVD caddy, be sure to get one which converts an SATAВ drive to the PATAinterface used for the DVD drive in old Macs. The ultimate choice is the HardWrk adapter, which comes complete with tools and an external caddy for the DVD drive youвЂ™ll be removing. A DVD to hard drive caddy converter kit вЂ“ the OptibayВ is the best option at $49, but I went with an even cheaper generic modelВ from eBay that required a little modification to fit correctly (IвЂ™ll detail this later).An SSD вЂ“ 60GB+ is fine, mine was about $100 from Amazon, the cheapest they had.Anti-static wrist strap, or lots of touching radiators.A small plastic spatula for lifting off ribbon cables.T6 Torx screwdriver вЂ“ though you can get away with a miniature flathead (I did).This will result in superb boot and application launch times, and who needs a DVD drive anyway in this day and age? You Will Need WeвЂ™ll then shift the current hard drive over to that, and place the SSD in the primary hard drive position. Today, weвЂ™ll be opening up the laptop, removing the DVD drive and replacing it with a hard drive caddy. Best of all you wonвЂ™t be sacrificing storage space, since weвЂ™ll be putting your old drive where the DVD drive was. Programs will launch a lot faster, your boot time will be cut dramatically, and itвЂ™ll feel like a new machine.

Basically theyвЂ™re solid state memory, meaning no moving parts and significantly better performance. Is your old Apple laptop starting to struggle? Is the boot time so long that you can actually go out and buy a coffee? If so, perhaps itвЂ™s time to think about upgrading your main system drive to a low cost SSD and getting rid of that useless old DVD drive.